SolaX X1-IES
The SolaX X1-IES stores 4.6 kWh usable. All-in-one: hybrid inverter stacked on high-voltage LFP battery modules with a BMS; solar connects on the DC side. Running essentials only, a full X1-IES-3.7K + 1 battery (5.1 kWh) lasts about 28.4 hours in a power cut.
A stackable all-in-one system: a single-phase hybrid inverter (2.5 to 8 kW) on top of 1–4 TP-HS50E battery modules of 4.6 kWh usable each, up to 18.4 kWh.
Last checked 27 Sept 2026 · Sources listed at the bottom of the page
- Continuous power per setup is the lower of the inverter rating and 3 kW rated power per battery module; each module can briefly deliver up to 5.1 kW.
- Round-trip efficiency isn't stated; the datasheet gives the inverter's maximum efficiency (97.6%), which is one conversion only.
- Warranty figures are from SolaX's global warranty terms (V1.7, for products sold from 10 September 2026). It doesn't mention the UK specifically; UK distributors may add their own terms.
- The system overview in the datasheet labels usable energy in "kW"; the battery table gives 4.6 kWh per module, which we use.
How long will it run your home?
Pick a setup and tick what you want to keep running. The maths is shown below the result.
Average draw 154 W from 4.37 kWh available.
Everything on at once: 580 W — within the 3 kW limit
- Starts from a full battery with 0% held back as reserve.
- 5% extra allowed for wiring and standby losses on top of the manufacturer's usable figure.
- Appliance figures are typical averages; your own may differ. Enter your own wattage for the most accurate result.
- Assumes no solar recharging during the outage.
Where the appliance figures come from
Power ratings are the Centre for Sustainable Energy's typical UK figures. How much of the time each appliance runs comes from average UK use measured in the Household Electricity Survey (2010–11), converted to an average draw; newer appliances often use less. Heat pump figures come from the Electrification of Heat trial. Anything marked “estimate” is ours.
| Appliance | Power | How much it runs |
|---|---|---|
| Fridge-freezer | CSE typical rating: fridge-freezer 300 W. Start-up surge (600 W) is an EnergyPicker estimateCentre for Sustainable Energy | UK average 427 kWh a year for households with a fridge-freezer (Household Electricity Survey), about 49 W on averageNational Energy Action, PDF p.6–7, section 1.2 (Household Electricity Survey averages) |
| LED lighting (whole house) | EnergyPicker estimate: about ten 10 W LED bulbsestimate | EnergyPicker estimate: on half the timeestimate |
| Wi-Fi router & broadband | CSE typical rating: broadband router 10 WCentre for Sustainable Energy | EnergyPicker estimate: always onestimate |
| Laptop & phone charging | CSE typical rating: laptop 50 WCentre for Sustainable Energy | EnergyPicker estimate: charging about 7 hours a dayestimate |
| TV (LCD) | CSE typical rating: LCD TV 120 WCentre for Sustainable Energy | EnergyPicker estimate: on about 6 hours a dayestimate |
| Gas boiler controls & pump | EnergyPicker estimate: check your boiler's manual for its electrical ratingestimate | EnergyPicker estimate: running half the time in winterestimate |
| Chest freezer | CSE typical rating: freezer 150 WCentre for Sustainable Energy | UK average 362 kWh a year for households with a chest freezer (Household Electricity Survey), about 41 W on averageNational Energy Action, PDF p.6–7, section 1.2 (Household Electricity Survey averages) |
| Kettle | CSE typical rating: kettle 3000 WCentre for Sustainable Energy | UK average 167 kWh a year for kettles (Household Electricity Survey), about 19 W on averageNational Energy Action, PDF p.6–7, section 1.2 (Household Electricity Survey averages) |
| Microwave | CSE typical rating: microwave 1000 WCentre for Sustainable Energy | UK average 56 kWh a year for microwaves (Household Electricity Survey), about 6 W on averageNational Energy Action, PDF p.6–7, section 1.2 (Household Electricity Survey averages) |
| Electric hob | CSE typical rating: hob 2000 WCentre for Sustainable Energy | UK average 226 kWh a year for hobs (Household Electricity Survey), about 26 W on averageNational Energy Action, PDF p.6–7, section 1.2 (Household Electricity Survey averages) |
| Electric oven | CSE typical rating: oven 2100 WCentre for Sustainable Energy | UK average 290 kWh a year for ovens (Household Electricity Survey), about 33 W on averageNational Energy Action, PDF p.6–7, section 1.2 (Household Electricity Survey averages) |
| Washing machine | CSE typical rating: washing machine 2100 WCentre for Sustainable Energy | UK average 166 kWh a year for washing machines (Household Electricity Survey), about 19 W on averageNational Energy Action, PDF p.6–7, section 1.2 (Household Electricity Survey averages) |
| Dishwasher | EnergyPicker estimate: CSE doesn't list dishwashers; check your model's rating plateestimate | UK average 294 kWh a year for dishwashers (Household Electricity Survey), about 34 W on averageNational Energy Action, PDF p.6–7, section 1.2 (Household Electricity Survey averages) |
| Tumble dryer (vented or condenser) | CSE typical rating: tumble dryer 2500 WCentre for Sustainable Energy | Energy labels give 560–640 kWh a year for condenser and vented dryers (160 cycles); we use 600 kWh, about 68 W on average. Heat pump dryers use far lessNational Energy Action, PDF p.34, energy label consumption |
| Electric shower | CSE typical rating: electric shower 9000 WCentre for Sustainable Energy | EnergyPicker estimate: about 15 minutes a dayestimate |
| Air-source heat pump (cold day, about −3°C) | Average, not peak: UK trial median 0.79 kWh per half hour at −3°C, i.e. 1.58 kW. The heat pump's own peak draw is higher; check its datasheetEnergy Systems Catapult, Table 10.1 (PDF p.79) | Treated as a steady average across the dayEnergy Systems Catapult, Table 10.1 (PDF p.79) |
| EV charger (7 kW) | EnergyPicker estimate: a typical single-phase home chargerestimate | EnergyPicker estimate: charging about 2.4 hours a dayestimate |
Setups you can buy
| Setup | Usable energy | Continuous power |
|---|---|---|
| X1-IES-3.7K + 1 battery (5.1 kWh) | 4.6 kWh | 3 kWcalculated |
| X1-IES-3.7K + 2 batteries (10.2 kWh) | 9.2 kWh | 3.68 kWcalculated |
| X1-IES-6K + 2 batteries (10.2 kWh) | 9.2 kWh | 6 kWcalculated |
| X1-IES-6K + 3 batteries (15.3 kWh) | 13.8 kWh | 6 kWcalculated |
| X1-IES-8K + 3 batteries (15.3 kWh) | 13.8 kWh | 8 kWcalculated |
| X1-IES-8K + 4 batteries (20.4 kWh, maximum) | 18.4 kWh | 8 kWcalculated |
Published UK prices
| SolaX X1-IES 3.7 kW inverter + 1 × TP-HS50E battery (5.1 kWh)Hardware only, before installation | £2,990£650 per usable kWhAIZO Quality Heating, seen 27 Sept 2026 |
|---|---|
| SolaX X1-IES 3.7 kW inverter + 2 × TP-HS50E battery (10.2 kWh)Hardware only, before installation | £4,200£457 per usable kWhAIZO Quality Heating, seen 27 Sept 2026 |
| SolaX X1-IES 6 kW inverter + 2 × TP-HS50E battery (10.2 kWh)Hardware only, before installation | £4,300£467 per usable kWhAIZO Quality Heating, seen 27 Sept 2026 |
| SolaX X1-IES 6 kW inverter + 3 × TP-HS50E battery (15.3 kWh)Hardware only, before installation | £5,900£428 per usable kWhAIZO Quality Heating, seen 27 Sept 2026 |
| SolaX X1-IES 8 kW inverter + 4 × TP-HS50E battery (20.4 kWh)Hardware only, before installation | £6,700£364 per usable kWhAIZO Quality Heating, seen 27 Sept 2026 |
Published prices, not quotes. See UK battery prices for VAT and what's included.
Full specifications
| Specification | Value | Source |
|---|---|---|
| Capacity | ||
| Usable capacity (per unit) | 4.6 kWhPer TP-HS50E module. SolaX notes usable energy may vary with inverter settings | SolaX Power datasheetp.2, Battery: Usable energy |
| Total (nominal) capacity | 5.1 kWhPer module (5.1 kWh / 50 Ah) | SolaX Power datasheetp.2, Battery: Rated capacity |
| Depth of discharge | Not documented in the sources we hold | |
| Battery chemistry | LFP (LiFePO₄) | SolaX Power datasheetp.2, Battery type |
| System | ||
| Maximum usable storage (expanded) | 18.4 kWh | SolaX Power datasheetp.2, System overview: 4 batteries |
| How it expands | 1–4 battery modules per inverter. Four modules need a second column and a Series Box | SolaX Power datasheetp.2, System overview and Battery: Composition |
| Maximum system power (expanded) | 8 kWWith the 8 kW inverter and 2 or more modules | SolaX Power datasheetp.2, System overview: Max. power |
| Architecture | All-in-one: hybrid inverter stacked on high-voltage LFP battery modules with a BMS; solar connects on the DC side | SolaX Power datasheetp.1–2 |
| Grid connection | Single phase, 220/230/240 V | SolaX Power datasheetp.2, Rated AC voltage |
| Power | ||
| Continuous power (per unit) | 3.68–8 kWX1-IES-3.7K: 3.68 kW · 5K: 5 kW · 6K: 6 kW · 8K: 8 kW (2.5 and 3 kW models also listed). Also limited by the batteries: 3 kW rated per module | SolaX Power datasheetp.2, AC output: Rated output power |
| Peak power | 7.36–16 kWcalculatedBackup peak for 10 seconds. Battery maximum power (5.1 kW per module, 8 kW per system) may limit thisHow: 2 × rated EPS output for 10 s: 3.7K 7.36 kVA, 8K 16 kVA | SolaX Power datasheetp.1, EPS output: Peak EPS output power |
| Peak duration | 10 s | SolaX Power datasheetp.1, Peak EPS output power |
| Max charge power | 5.1 kWPer module maximum (rated 3 kW); up to 8 kW for a system with 2 or more modules on the 8 kW inverter | SolaX Power datasheetp.2, Battery: Max. power |
| Round-trip efficiency | Not documented in the sources we hold | |
| Solar | ||
| Max solar input | 7.4–16 kW3.7K: 7.4 kWp · 5K: 10 kWp · 6K: 12 kWp · 8K: 16 kWp | SolaX Power datasheetp.2, PV input: Max. recommended PV array power |
| Solar MPPT inputs | 2 (up to 3.7 kW) or 3 (5–8 kW) | SolaX Power datasheetp.2, No. of MPP trackers |
| Backup | ||
| Backup switchover time | 10 msLess than 10 ms | SolaX Power datasheetp.1, EPS output: Switchover time |
| Backup needs | Built-in EPS (backup) output | SolaX Power datasheetp.1, EPS (off-grid) output (with battery) |
| Physical | ||
| Ingress rating | IP66 | SolaX Power datasheetp.2, System overview: Ingress protection |
| Indoor / outdoor | Indoor and outdoor (IP66)calculatedHow: IP66 rating and −30 to 53°C system range | SolaX Power datasheetp.2 |
| Operating temperature | −30°C to 53°C (system) | SolaX Power datasheetp.2, System overview: Operation temperature range |
| Dimensions | 730 × 1226 × 210 (inverter + 2 modules)W × H × D. 1 module: 908 mm high; 3 modules: 1544 mm; 4 modules: two columns | SolaX Power datasheetp.2, System overview: Dimensions |
| Weight | 87.2–181.2 kgInverter + 1 module 87.2 kg, + 3 modules 181.2 kg (47 kg per module) | SolaX Power datasheetp.2, System overview: Net weight |
| Mounting | Not documented in the sources we hold | |
| Warranty | ||
| Stated cycle life | 6,000 cyclesMore than 6,000 cycles | SolaX Power datasheetp.2, Battery: Cycle life |
| Warranty | 10 yearsBattery modules. The X1-IES inverter has 5 years, upgraded free to 10 years if it is connected to SolaX Cloud and uploads data | SolaX Power warranty§2, Table 1 (T-BAT-SYS-HV-S50E, TP-HS50E) |
| Capacity guaranteed at end of warranty | 70%70% of nominal energy (5.1 kWh per module) | SolaX Power warranty§3, Performance warranty of battery |
| Warranty throughput limit | 15.9 MWhPer module; whichever comes first: 10 years or 15.9 MWh | SolaX Power warranty§3, TP-HS50E row |
| Warranty conditions | Bought from an authorised reseller and installed by a qualified installer. Batteries added later should be added within a year of installation. The inverter warranty is 5 years unless it's connected to SolaX Cloud. | SolaX Power warranty§1, §2 and §4 |
| Compliance | ||
| UK grid compliance | G98, G99 | SolaX Power datasheetp.1, Certifications |
Questions people ask
How much usable capacity does the SolaX X1-IES have?
4.6 kWh (Per TP-HS50E module. SolaX notes usable energy may vary with inverter settings).
Can the SolaX X1-IES be expanded?
1–4 battery modules per inverter. Four modules need a second column and a Series Box. Maximum usable storage: 18.4 kWh.
How long will the SolaX X1-IES run a house in a power cut?
Running essentials only (fridge-freezer, lights, Wi-Fi, TV and device charging, about 154 W on average), a full X1-IES-3.7K + 1 battery (5.1 kWh) lasts roughly 28.4 hours. Heavy loads such as a heat pump, electric shower or EV charger cut this sharply. Use the calculator on this page with your own appliances.
What warranty does the SolaX X1-IES have in the UK?
10 years, guaranteeing 70% of capacity or 15.9 MWh of throughput, whichever comes first. Battery modules. The X1-IES inverter has 5 years, upgraded free to 10 years if it is connected to SolaX Cloud and uploads data.
What does the SolaX X1-IES need to provide backup power?
Built-in EPS (backup) output.
Head-to-head comparisons
SolaX X1-IES vs Tesla Powerwall 3
Price, capacity, power, warranty and runtime side by side.
SolaX X1-IES vs Fox ESS EVO 10
Price, capacity, power, warranty and runtime side by side.
SolaX X1-IES vs Sigenergy SigenStor
Price, capacity, power, warranty and runtime side by side.
Guides for the SolaX X1-IES
- Does the SolaX X1-IES work with Intelligent Octopus Flux?Not on Octopus's list.
- Does the SolaX X1-IES work with Octopus Charge Pack?Coming soon, says Octopus. Charge Pack works on Go, Intelligent Go, Flexible and fixed tariffs.
- How many X1-IES units do I need?Size it from your electricity use, heat pump, EV and backup plans.
- Can the SolaX X1-IES run a heat pump?How much of a cold winter day it covers.
Other batteries
Enphase IQ Battery 5P
An AC-coupled 5 kWh battery with six built-in microinverters, so it can be added to most existing solar systems. Up to seven can be combined in the UK.
myenergi libbi
A UK-designed modular battery with a 3.68 kW or 5 kW hybrid inverter and 1–4 battery modules (4.6 kWh usable each). Built to work with myenergi's zappi and eddi.
SolarEdge Home Battery 400V
A 9.7 kWh high-voltage battery that pairs with SolarEdge's single-phase Home Hub inverter. Up to three batteries per inverter. Octopus lists SolarEdge for Intelligent Octopus Flux.
Huawei LUNA2000-S1
A modular high-voltage battery with 6.9 kWh modules (1–3 per stack, up to 20.7 kWh). Used with Huawei's SUN2000 hybrid inverters.
Sunsynk W5.3 with ECCO inverter
A 5.32 kWh, 48 V wall-mounted IP65 battery module (4.79 kWh usable) used with Sunsynk's ECCO hybrid inverters. Add modules in parallel for more storage.
EcoFlow OCEAN 2
EcoFlow's second-generation stacked system: a single-phase hybrid inverter (3 to 6 kW) on top of OCEAN 2 LFP batteries of 4.87 or 7.76 kWh usable, up to six per stack.
AlphaESS SMILE-G3
AlphaESS's stacked single-phase system: a 3.68 or 5 kW hybrid inverter on top of one to four LFP battery modules of 4.56 or 9.12 kWh usable, up to 36.5 kWh.
Sungrow SBR
Sungrow's stackable high-voltage battery: 3.2 kWh LFP modules, 6.4 to 25.6 kWh per stack, all of it usable. Paired here with Sungrow's single-phase SH RS hybrid inverter (3 to 6 kW), which takes up to SBR192 (19.2 kWh).
Sources
- SolaX X1-IES Datasheet (EN) V1.7 — SolaX Power, V1.7. Retrieved 27 Sept 2026. Two-page PDF: page 1 holds the EPS, efficiency and general tables; page 2 the system overview, PV, AC and battery tables.
- SolaX Warranty Terms & Conditions (V1.7, Global version) — SolaX Power, V1.7. Retrieved 27 Sept 2026. Applies to SolaX products sold or installed from 10 September 2026.
Spotted an error? Every figure above links to the document it came from. See how we check data.