Sunsynk W5.3 with ECCO inverter
The Sunsynk W5.3 with ECCO inverter stores 4.79 kWh usable per module. 48 V low-voltage battery modules with a Sunsynk ECCO hybrid inverter; the inverter supports DC or AC coupling to existing solar. Running essentials only, a full ECCO 3.6 kW + 2 × W5.3 (9.6 kWh) lasts about 2 days 11 hours in a power cut.
A 5.32 kWh, 48 V wall-mounted IP65 battery module (4.79 kWh usable) used with Sunsynk's ECCO hybrid inverters. Add modules in parallel for more storage.
Last checked 29 Sept 2026 · Sources listed at the bottom of the page
- Sunsynk recommends 50 A per module (about 2.5 kW) and allows up to 100 A. With only one or two modules, the full inverter output may not be sustained for long.
- Sunsynk's UK warranty terms don't guarantee a minimum capacity; the W5.3 datasheet gives a 16 MWh warranty energy limit at 70% end of life.
- Our W5.3 datasheet is version 1 (May 2024), a copy published by a UK distributor. Older systems use the 5.12 kWh L5.1 (4.61 kWh usable), which has the same size and current limits.
- Round-trip efficiency isn't stated on the battery datasheet.
- Our ECCO inverter datasheet is version 4 (March 2023), the newest we found for the 3.6 kW and 5 kW models.
How long will it run your home?
Pick a setup and tick what you want to keep running. The maths is shown below the result.
Average draw 154 W from 9.1 kWh available.
Everything on at once: 580 W — within the 3.6 kW limit
- Starts from a full battery with 0% held back as reserve.
- 5% extra allowed for wiring and standby losses on top of the manufacturer's usable figure.
- Appliance figures are typical averages; your own may differ. Enter your own wattage for the most accurate result.
- Assumes no solar recharging during the outage.
Where the appliance figures come from
Power ratings are the Centre for Sustainable Energy's typical UK figures. How much of the time each appliance runs comes from average UK use measured in the Household Electricity Survey (2010–11), converted to an average draw; newer appliances often use less. Heat pump figures come from the Electrification of Heat trial. Anything marked “estimate” is ours.
| Appliance | Power | How much it runs |
|---|---|---|
| Fridge-freezer | CSE typical rating: fridge-freezer 300 W. Start-up surge (600 W) is an EnergyPicker estimateCentre for Sustainable Energy | UK average 427 kWh a year for households with a fridge-freezer (Household Electricity Survey), about 49 W on averageNational Energy Action, PDF p.6–7, section 1.2 (Household Electricity Survey averages) |
| LED lighting (whole house) | EnergyPicker estimate: about ten 10 W LED bulbsestimate | EnergyPicker estimate: on half the timeestimate |
| Wi-Fi router & broadband | CSE typical rating: broadband router 10 WCentre for Sustainable Energy | EnergyPicker estimate: always onestimate |
| Laptop & phone charging | CSE typical rating: laptop 50 WCentre for Sustainable Energy | EnergyPicker estimate: charging about 7 hours a dayestimate |
| TV (LCD) | CSE typical rating: LCD TV 120 WCentre for Sustainable Energy | EnergyPicker estimate: on about 6 hours a dayestimate |
| Gas boiler controls & pump | EnergyPicker estimate: check your boiler's manual for its electrical ratingestimate | EnergyPicker estimate: running half the time in winterestimate |
| Chest freezer | CSE typical rating: freezer 150 WCentre for Sustainable Energy | UK average 362 kWh a year for households with a chest freezer (Household Electricity Survey), about 41 W on averageNational Energy Action, PDF p.6–7, section 1.2 (Household Electricity Survey averages) |
| Kettle | CSE typical rating: kettle 3000 WCentre for Sustainable Energy | UK average 167 kWh a year for kettles (Household Electricity Survey), about 19 W on averageNational Energy Action, PDF p.6–7, section 1.2 (Household Electricity Survey averages) |
| Microwave | CSE typical rating: microwave 1000 WCentre for Sustainable Energy | UK average 56 kWh a year for microwaves (Household Electricity Survey), about 6 W on averageNational Energy Action, PDF p.6–7, section 1.2 (Household Electricity Survey averages) |
| Electric hob | CSE typical rating: hob 2000 WCentre for Sustainable Energy | UK average 226 kWh a year for hobs (Household Electricity Survey), about 26 W on averageNational Energy Action, PDF p.6–7, section 1.2 (Household Electricity Survey averages) |
| Electric oven | CSE typical rating: oven 2100 WCentre for Sustainable Energy | UK average 290 kWh a year for ovens (Household Electricity Survey), about 33 W on averageNational Energy Action, PDF p.6–7, section 1.2 (Household Electricity Survey averages) |
| Washing machine | CSE typical rating: washing machine 2100 WCentre for Sustainable Energy | UK average 166 kWh a year for washing machines (Household Electricity Survey), about 19 W on averageNational Energy Action, PDF p.6–7, section 1.2 (Household Electricity Survey averages) |
| Dishwasher | EnergyPicker estimate: CSE doesn't list dishwashers; check your model's rating plateestimate | UK average 294 kWh a year for dishwashers (Household Electricity Survey), about 34 W on averageNational Energy Action, PDF p.6–7, section 1.2 (Household Electricity Survey averages) |
| Tumble dryer (vented or condenser) | CSE typical rating: tumble dryer 2500 WCentre for Sustainable Energy | Energy labels give 560–640 kWh a year for condenser and vented dryers (160 cycles); we use 600 kWh, about 68 W on average. Heat pump dryers use far lessNational Energy Action, PDF p.34, energy label consumption |
| Electric shower | CSE typical rating: electric shower 9000 WCentre for Sustainable Energy | EnergyPicker estimate: about 15 minutes a dayestimate |
| Air-source heat pump (cold day, about −3°C) | Average, not peak: UK trial median 0.79 kWh per half hour at −3°C, i.e. 1.58 kW. The heat pump's own peak draw is higher; check its datasheetEnergy Systems Catapult, Table 10.1 (PDF p.79) | Treated as a steady average across the dayEnergy Systems Catapult, Table 10.1 (PDF p.79) |
| EV charger (7 kW) | EnergyPicker estimate: a typical single-phase home chargerestimate | EnergyPicker estimate: charging about 2.4 hours a dayestimate |
Setups you can buy
| Setup | Usable energy | Continuous power |
|---|---|---|
| ECCO 3.6 kW + 2 × W5.3 (9.6 kWh) | 9.58 kWhcalculated | 3.6 kW |
| ECCO 5 kW + 2 × W5.3 (9.6 kWh) | 9.58 kWhcalculated | 5 kW |
| ECCO 5 kW + 3 × W5.3 (14.4 kWh) | 14.37 kWhcalculated | 5 kW |
| ECCO 5 kW + 4 × W5.3 (19.2 kWh) | 19.16 kWhcalculated | 5 kW |
| ECCO 5 kW + 6 × W5.3 (28.7 kWh) | 28.74 kWhcalculated | 5 kW |
Published UK prices
| Sunsynk W5.3 battery module, white (one 5.32 kWh module, with isolator and cables)Hardware only, before installation | £1,395£291 per usable kWhNot included: A Sunsynk hybrid inverter (for example an ECCO)AIZO Quality Heating, seen 29 Sept 2026 |
|---|---|
| Sunsynk W5.3 battery module, black (one 5.32 kWh module, with isolator and cables)Hardware only, before installation | £1,450£303 per usable kWhNot included: A Sunsynk hybrid inverter (for example an ECCO)AIZO Quality Heating, seen 29 Sept 2026 |
Published prices, not quotes. See UK battery prices for VAT and what's included.
Full specifications
| Specification | Value | Source |
|---|---|---|
| Capacity | ||
| Usable capacity (per unit) | 4.79 kWhPer module; 90% depth of discharge, 0.5C, 25°C | Sunsynk datasheetp.2, Usable Energy, footnote 1 |
| Total (nominal) capacity | 5.32 kWhPer module (104 Ah, 51.2 V) | Sunsynk datasheetp.2, Energy |
| Depth of discharge | 90% | Sunsynk datasheetp.2, Recommend Depth of Discharge |
| Battery chemistry | LFP (LiFePO₄) | Sunsynk datasheetp.2 |
| System | ||
| Maximum usable storage (expanded) | 153.28 kWhcalculatedBattery bank limit; each inverter's battery current limit appliesHow: 32 × 4.79 kWh usable | Sunsynk datasheetp.2, Scalability; Usable Energy |
| How it expands | Up to 32 modules in parallel (170 kWh total energy) | Sunsynk datasheetp.2, Scalability |
| Maximum system power (expanded) | Not documented in the sources we hold | |
| Architecture | 48 V low-voltage battery modules with a Sunsynk ECCO hybrid inverter; the inverter supports DC or AC coupling to existing solar | Sunsynk datasheetp.1, features: "DC couple and AC couple to retrofit existing solar system" |
| Grid connection | Single phase | Sunsynk datasheetp.2, Grid Type |
| Power | ||
| Continuous power (per unit) | 3.6–5 kWECCO 3.6K: 3.6 kW · ECCO 5K: 5 kW (larger ECCO models also available) | Sunsynk datasheetp.2, Rated AC Output and UPS Power |
| Peak power | 7.2–10 kWcalculatedInverter: 2 × rated power for 10 s, off-grid. The batteries' current limits may allow less.How: 2 × rated power: 3.6 kW model 7.2 kW, 5 kW model 10 kW | Sunsynk datasheetp.2, Peak Power (off-grid) |
| Peak duration | 10 s | Sunsynk datasheetp.2 |
| Max charge power | Not documented in the sources we hold | |
| Round-trip efficiency | Not documented in the sources we hold | |
| Solar | ||
| Max solar input | 6.5–7 kWECCO 5K: 6.5 kW · ECCO 3.6K: 7 kW | Sunsynk datasheetp.2, Max. DC Input Power |
| Solar MPPT inputs | 2 | Sunsynk datasheetp.2 |
| Backup | ||
| Backup switchover time | Not documented in the sources we hold | |
| Backup needs | Not documented in the sources we hold | |
| Physical | ||
| Ingress rating | IP65 (battery) | Sunsynk datasheetp.2, IP Rating of Enclosure |
| Indoor / outdoor | Not documented in the sources we hold | |
| Operating temperature | Charge −10°C to 55°C; discharge −20°C to 55°C | Sunsynk datasheetp.2, Working Temperature |
| Dimensions | 440 × 620 × 135 per moduleW × H × D, excluding terminals, breaker, hanging boards and pedestal | Sunsynk datasheetp.2, Dimension |
| Weight | 46 kgPer module; ECCO inverter 20.5 kg | Sunsynk datasheetp.2, Weight |
| Mounting | Wall-mounted (supports 19-inch cabinet) | Sunsynk datasheetp.2, Installation |
| Warranty | ||
| Stated cycle life | 6,000 cyclesAt least 6,000 cycles at 25°C, 90% depth of discharge, to 70% end of life | Sunsynk datasheetp.2, Cycle Life |
| Warranty | 10 yearsBattery cells: 10 years or 6,000 cycles. Battery BMS: 5 years | Sunsynk warrantyp.1, §2 Battery warranty |
| Capacity guaranteed at end of warranty | Not documented in the sources we hold | |
| Warranty throughput limit | 16 MWhPer module, at 70% end of life; the datasheet says the warranty ends at the warranty period or this energy, whichever comes first | Sunsynk datasheetp.2, Life Cycle Power During Warranty Period, footnote 3 |
| Warranty conditions | After year 5, faulty cells are replaced free but labour isn't covered. Must be bought from Sunsynk or an authorised reseller, installed in a covered country (the UK is included) and cycled no more than 700 times a year. No capacity-retention figure is given. | Sunsynk warrantyp.1, §2, §4 and §5 |
| Compliance | ||
| UK grid compliance | G98, G99 (ECCO inverter) | Sunsynk datasheetp.3, Grid Regulation |
Questions people ask
How much usable capacity does the Sunsynk W5.3 with ECCO inverter have?
4.79 kWh (Per module; 90% depth of discharge, 0.5C, 25°C).
Can the Sunsynk W5.3 with ECCO inverter be expanded?
Up to 32 modules in parallel (170 kWh total energy). Maximum usable storage: 153.28 kWh (calculated).
How long will the Sunsynk W5.3 with ECCO inverter run a house in a power cut?
Running essentials only (fridge-freezer, lights, Wi-Fi, TV and device charging, about 154 W on average), a full ECCO 3.6 kW + 2 × W5.3 (9.6 kWh) lasts roughly 2 days 11 hours. Heavy loads such as a heat pump, electric shower or EV charger cut this sharply. Use the calculator on this page with your own appliances.
What warranty does the Sunsynk W5.3 with ECCO inverter have in the UK?
10 years or 16 MWh of throughput, whichever comes first. Battery cells: 10 years or 6,000 cycles. Battery BMS: 5 years.
Head-to-head comparisons
Guides for the Sunsynk W5.3 with ECCO inverter
- Adding a battery to a SolarEdge inverterWhere the Sunsynk W5.3 with ECCO inverter is documented as an option for this system.
- Adding a battery to a Solis inverterWhere the Sunsynk W5.3 with ECCO inverter is documented as an option for this system.
- Adding a battery to a Huawei inverterWhere the Sunsynk W5.3 with ECCO inverter is documented as an option for this system.
- Adding a battery to a Growatt inverterWhere the Sunsynk W5.3 with ECCO inverter is documented as an option for this system.
- Adding a battery to a Sungrow inverterWhere the Sunsynk W5.3 with ECCO inverter is documented as an option for this system.
- Adding a battery to a Fronius inverterWhere the Sunsynk W5.3 with ECCO inverter is documented as an option for this system.
- Adding a battery to a GoodWe inverterWhere the Sunsynk W5.3 with ECCO inverter is documented as an option for this system.
- Adding batteries to a Sunsynk inverterWhere the Sunsynk W5.3 with ECCO inverter is documented as an option for this system.
- Does the Sunsynk W5.3 with ECCO inverter work with Intelligent Octopus Flux?Not on Octopus's list.
- Does the Sunsynk W5.3 with ECCO inverter work with Octopus Charge Pack?Not on Octopus's list. Charge Pack works on Go, Intelligent Go, Flexible and fixed tariffs.
- How many W5.3 with ECCO inverter units do I need?Size it from your electricity use, heat pump, EV and backup plans.
- Can the Sunsynk W5.3 with ECCO inverter run a heat pump?How much of a cold winter day it covers.
Other batteries
Tesla Powerwall 3
An all-in-one home battery with a built-in solar inverter. One unit stores 13.5 kWh and can be expanded with up to three Expansion units.
Sigenergy SigenStor
A stackable system: a Sigen Energy Controller (hybrid inverter) with 1–6 Sigen Battery modules of 5.84 kWh (BAT 6.0) or 8.76 kWh (BAT 10.0) usable each.
Enphase IQ Battery 5P
An AC-coupled 5 kWh battery with six built-in microinverters, so it can be added to most existing solar systems. Up to seven can be combined in the UK.
myenergi libbi
A UK-designed modular battery with a 3.68 kW or 5 kW hybrid inverter and 1–4 battery modules (4.6 kWh usable each). Built to work with myenergi's zappi and eddi.
SolarEdge Home Battery 400V
A 9.7 kWh high-voltage battery that pairs with SolarEdge's single-phase Home Hub inverter. Up to three batteries per inverter. Octopus lists SolarEdge for Intelligent Octopus Flux.
Huawei LUNA2000-S1
A modular high-voltage battery with 6.9 kWh modules (1–3 per stack, up to 20.7 kWh). Used with Huawei's SUN2000 hybrid inverters.
SolaX X1-IES
A stackable all-in-one system: a single-phase hybrid inverter (2.5 to 8 kW) on top of 1–4 TP-HS50E battery modules of 4.6 kWh usable each, up to 18.4 kWh.
EcoFlow OCEAN 2
EcoFlow's second-generation stacked system: a single-phase hybrid inverter (3 to 6 kW) on top of OCEAN 2 LFP batteries of 4.87 or 7.76 kWh usable, up to six per stack.
AlphaESS SMILE-G3
AlphaESS's stacked single-phase system: a 3.68 or 5 kW hybrid inverter on top of one to four LFP battery modules of 4.56 or 9.12 kWh usable, up to 36.5 kWh.
Sungrow SBR
Sungrow's stackable high-voltage battery: 3.2 kWh LFP modules, 6.4 to 25.6 kWh per stack, all of it usable. Paired here with Sungrow's single-phase SH RS hybrid inverter (3 to 6 kW), which takes up to SBR192 (19.2 kWh).
Sources
- SUNSYNK-W5.3 datasheet — Sunsynk, v.1 (22/05/24). Retrieved 29 Sept 2026. Official Sunsynk datasheet (lists Sunsynk UK Ltd, Widnes) hosted by UK distributor HDM Solar.
- ECCO Hybrid Inverter SUN-3.6/5/6/7.6/8K-SG05LP1-EU datasheet — Sunsynk, v.4 (29/03/23). Retrieved 26 Sept 2026. Official Sunsynk datasheet hosted by UK retailer Bimble Solar.
- Sunsynk ECCO SUN-3.6/5/6/7.6/8K-SG05LP1-EU datasheet (2022 edition) — Sunsynk. Retrieved 26 Sept 2026. Earlier edition hosted by UK retailer Dragons Breath Solar. It states the ECCO supports AC coupling to retrofit existing solar; the later v4 datasheet doesn't repeat the feature list.
- Manufacturer's Warranty — Warranty Agreement Terms and Conditions — Sunsynk. Retrieved 26 Sept 2026. Published on Sunsynk UK's website (Sunsynk Ltd, Widnes). The PDF is a scanned image; we read it visually.
Spotted an error? Every figure above links to the document it came from. See how we check data.