Sigenergy SigenStor
The Sigenergy SigenStor stores 5.84–8.76 kWh usable per module. Modular: Energy Controller (hybrid inverter, solar on DC side) plus stacked battery modules. The batteries also work with Sigen Hybrid SP2/TP2 inverters via the SigenStor BC. Running essentials only, a full 6.0 SP controller + 1 × BAT 6.0 lasts about 36.1 hours in a power cut.
A stackable system: a Sigen Energy Controller (hybrid inverter) with 1–6 Sigen Battery modules of 5.84 kWh (BAT 6.0) or 8.76 kWh (BAT 10.0) usable each.
Last checked 26 Sept 2026 · Sources listed at the bottom of the page
- Battery figures are for the current BAT 6.0 and BAT 10.0 modules (Sigenergy datasheet, September 2025). Older systems use BAT 5.0 (5.2 kWh usable) or BAT 8.0 (7.8 kWh usable) modules.
- Warranty figures are from Sigenergy's Europe warranty (May 2025). It doesn't name the UK; confirm UK cover with your installer. The earlier (2024) edition promised 70% capacity; the 2025 edition promises 60% with higher throughput limits.
- Round-trip efficiency is not stated as a single figure in the datasheets we hold.
- UK retailers also sell 8, 10 and 12 kW single-phase controllers; our controller datasheet covers the 3.0–6.0 SP range, so setups here use the 6.0 SP.
How long will it run your home?
Pick a setup and tick what you want to keep running. The maths is shown below the result.
Average draw 154 W from 5.55 kWh available.
Everything on at once: 580 W — within the 3 kW limit
- Starts from a full battery with 0% held back as reserve.
- 5% extra allowed for wiring and standby losses on top of the manufacturer's usable figure.
- Appliance figures are typical averages; your own may differ. Enter your own wattage for the most accurate result.
- Assumes no solar recharging during the outage.
Where the appliance figures come from
Power ratings are the Centre for Sustainable Energy's typical UK figures. How much of the time each appliance runs comes from average UK use measured in the Household Electricity Survey (2010–11), converted to an average draw; newer appliances often use less. Heat pump figures come from the Electrification of Heat trial. Anything marked “estimate” is ours.
| Appliance | Power | How much it runs |
|---|---|---|
| Fridge-freezer | CSE typical rating: fridge-freezer 300 W. Start-up surge (600 W) is an EnergyPicker estimateCentre for Sustainable Energy | UK average 427 kWh a year for households with a fridge-freezer (Household Electricity Survey), about 49 W on averageNational Energy Action, PDF p.6–7, section 1.2 (Household Electricity Survey averages) |
| LED lighting (whole house) | EnergyPicker estimate: about ten 10 W LED bulbsestimate | EnergyPicker estimate: on half the timeestimate |
| Wi-Fi router & broadband | CSE typical rating: broadband router 10 WCentre for Sustainable Energy | EnergyPicker estimate: always onestimate |
| Laptop & phone charging | CSE typical rating: laptop 50 WCentre for Sustainable Energy | EnergyPicker estimate: charging about 7 hours a dayestimate |
| TV (LCD) | CSE typical rating: LCD TV 120 WCentre for Sustainable Energy | EnergyPicker estimate: on about 6 hours a dayestimate |
| Gas boiler controls & pump | EnergyPicker estimate: check your boiler's manual for its electrical ratingestimate | EnergyPicker estimate: running half the time in winterestimate |
| Chest freezer | CSE typical rating: freezer 150 WCentre for Sustainable Energy | UK average 362 kWh a year for households with a chest freezer (Household Electricity Survey), about 41 W on averageNational Energy Action, PDF p.6–7, section 1.2 (Household Electricity Survey averages) |
| Kettle | CSE typical rating: kettle 3000 WCentre for Sustainable Energy | UK average 167 kWh a year for kettles (Household Electricity Survey), about 19 W on averageNational Energy Action, PDF p.6–7, section 1.2 (Household Electricity Survey averages) |
| Microwave | CSE typical rating: microwave 1000 WCentre for Sustainable Energy | UK average 56 kWh a year for microwaves (Household Electricity Survey), about 6 W on averageNational Energy Action, PDF p.6–7, section 1.2 (Household Electricity Survey averages) |
| Electric hob | CSE typical rating: hob 2000 WCentre for Sustainable Energy | UK average 226 kWh a year for hobs (Household Electricity Survey), about 26 W on averageNational Energy Action, PDF p.6–7, section 1.2 (Household Electricity Survey averages) |
| Electric oven | CSE typical rating: oven 2100 WCentre for Sustainable Energy | UK average 290 kWh a year for ovens (Household Electricity Survey), about 33 W on averageNational Energy Action, PDF p.6–7, section 1.2 (Household Electricity Survey averages) |
| Washing machine | CSE typical rating: washing machine 2100 WCentre for Sustainable Energy | UK average 166 kWh a year for washing machines (Household Electricity Survey), about 19 W on averageNational Energy Action, PDF p.6–7, section 1.2 (Household Electricity Survey averages) |
| Dishwasher | EnergyPicker estimate: CSE doesn't list dishwashers; check your model's rating plateestimate | UK average 294 kWh a year for dishwashers (Household Electricity Survey), about 34 W on averageNational Energy Action, PDF p.6–7, section 1.2 (Household Electricity Survey averages) |
| Tumble dryer (vented or condenser) | CSE typical rating: tumble dryer 2500 WCentre for Sustainable Energy | Energy labels give 560–640 kWh a year for condenser and vented dryers (160 cycles); we use 600 kWh, about 68 W on average. Heat pump dryers use far lessNational Energy Action, PDF p.34, energy label consumption |
| Electric shower | CSE typical rating: electric shower 9000 WCentre for Sustainable Energy | EnergyPicker estimate: about 15 minutes a dayestimate |
| Air-source heat pump (cold day, about −3°C) | Average, not peak: UK trial median 0.79 kWh per half hour at −3°C, i.e. 1.58 kW. The heat pump's own peak draw is higher; check its datasheetEnergy Systems Catapult, Table 10.1 (PDF p.79) | Treated as a steady average across the dayEnergy Systems Catapult, Table 10.1 (PDF p.79) |
| EV charger (7 kW) | EnergyPicker estimate: a typical single-phase home chargerestimate | EnergyPicker estimate: charging about 2.4 hours a dayestimate |
Setups you can buy
| Setup | Usable energy | Continuous power |
|---|---|---|
| 6.0 SP controller + 1 × BAT 6.0 | 5.84 kWh | 3 kWcalculated |
| 6.0 SP controller + 1 × BAT 10.0 | 8.76 kWh | 4.6 kWcalculated |
| 6.0 SP controller + 2 × BAT 10.0 | 17.52 kWhcalculated | 6 kWcalculated |
| 6.0 SP controller + 3 × BAT 10.0 | 26.28 kWhcalculated | 6 kWcalculated |
| 6.0 SP controller + 4 × BAT 10.0 | 35.04 kWhcalculated | 6 kWcalculated |
| 6.0 SP controller + 5 × BAT 10.0 | 43.8 kWhcalculated | 6 kWcalculated |
| 6.0 SP controller + 6 × BAT 10.0 (maximum) | 52.56 kWhcalculated | 6 kWcalculated |
Published UK prices
| Sigenergy SigenStor BAT 6.0 battery module (one 5.84 kWh module)Hardware only, before installation | £2,500£428 per usable kWhNot included: A SigenStor Energy Controller (single-phase controllers listed below)AIZO Quality Heating, seen 27 Sept 2026 |
|---|---|
| Sigenergy SigenStor BAT 10.0 battery module (one 8.76 kWh module)Hardware only, before installation | £2,990£341 per usable kWhNot included: A SigenStor Energy Controller (single-phase controllers listed below)AIZO Quality Heating, seen 27 Sept 2026 |
| Sigenergy SigenStor Energy Controller 6.0 SP (single-phase hybrid inverter, no battery)Hardware only, before installation | £1,270AIZO Quality Heating, seen 27 Sept 2026 |
Published prices, not quotes. See UK battery prices for VAT and what's included.
Full specifications
| Specification | Value | Source |
|---|---|---|
| Capacity | ||
| Usable capacity (per unit) | 5.84–8.76 kWhPer module: BAT 6.0 = 5.84 kWh, BAT 10.0 = 8.76 kWh (100% depth of discharge, 0.2C, 25°C, start of life) | Sigenergy datasheetp.2, Usable energy capacity |
| Total (nominal) capacity | 6.02–9.04 kWhPer module: 6.02 / 9.04 kWh | Sigenergy datasheetp.2, Total energy capacity |
| Depth of discharge | 100%Must be recharged within 7 days of being fully discharged | Sigenergy datasheetp.2, Depth of discharge |
| Battery chemistry | LFP (LiFePO₄), 314 Ah cells | Sigenergy datasheetp.2, Battery type and Cell capacity |
| System | ||
| Maximum usable storage (expanded) | 52.56 kWhcalculatedPer controllerHow: 6 × 8.76 kWh (BAT 10.0) | Sigenergy datasheet |
| How it expands | 1–6 battery modules per controller | Sigenergy datasheetp.2, Number of modules per controller |
| Maximum system power (expanded) | Not documented in the sources we hold | |
| Architecture | Modular: Energy Controller (hybrid inverter, solar on DC side) plus stacked battery modules. The batteries also work with Sigen Hybrid SP2/TP2 inverters via the SigenStor BC. | Sigenergy datasheetp.2, Compatible inverters and footnote 4 |
| Grid connection | Single phase (3–6 kW) or three phase (5–25 kW) controllers | Sigenergy datasheetp.2 |
| Power | ||
| Continuous power (per unit) | 3–6 kWSingle-phase controllers 3.0–6.0 kW; also limited by the battery modules (3 kW per BAT 6.0, 4.6 kW per BAT 10.0) | Sigenergy datasheetp.2, Single-phase controller, nominal output power |
| Peak power | 4.5–9 kWSingle-phase backup peak for 10 seconds, 4.5–9 kW by controller. Battery peak: 4.5 kW per BAT 6.0, 6.9 kW per BAT 10.0 | Sigenergy datasheetp.2, AC output (backup), peak 10 s |
| Peak duration | 10 s | Sigenergy datasheetp.2 |
| Max charge power | 3–4.6 kWPer module: 3 kW (BAT 6.0), 4.6 kW (BAT 10.0) | Sigenergy datasheetp.2, Max. charge / discharge power |
| Round-trip efficiency | Not documented in the sources we hold | |
| Solar | ||
| Max solar input | 6–12 kWSingle-phase controllers 3.0–6.0 SP | Sigenergy datasheetp.2, DC input |
| Solar MPPT inputs | 2Single-phase controllers | Sigenergy datasheetp.2 |
| Backup | ||
| Backup switchover time | 0 msNeeds the Sigen Energy Gateway; load-side disruption | Sigenergy datasheetp.2, footnote 1 |
| Backup needs | Sigen Energy Gateway | Sigenergy datasheetp.2, footnote 1 |
| Physical | ||
| Ingress rating | IP66 | Sigenergy datasheetp.2, System ingress protection rating |
| Indoor / outdoor | Not documented in the sources we hold | |
| Operating temperature | −20°C to 55°C (battery) | Sigenergy datasheetp.2, Operating temperature range |
| Dimensions | 767 × 270 × 265 (per module)W × H × D | Sigenergy datasheetp.2 |
| Weight | 62–78 kgPer module: 62 kg (BAT 6.0), 78 kg (BAT 10.0) | Sigenergy datasheetp.2, Weight |
| Mounting | Floor standing or wall mounted | Sigenergy datasheetp.2, Installation method |
| Warranty | ||
| Stated cycle life | 10,000 cyclesBattery cell maker's figure: 25°C, 0.5C charge and discharge, to 60% state of health | Sigenergy datasheetp.2, Cycle life, footnote 1 |
| Warranty | 10 yearsSigenStor BAT 5.0/6.0/8.0/10.0 and EC SP/TP controllers, installed on or after 1 June 2023 | Sigenergy warrantyp.1, Limited Product Warranty table |
| Capacity guaranteed at end of warranty | 60%60% of usable energy for 10 years or the minimum throughput, whichever comes first | Sigenergy warrantyp.1, Limited Performance Warranty |
| Warranty throughput limit | 20.44–30.66 MWhPer module: BAT 6.0 = 20.44 MWh, BAT 10.0 = 30.66 MWh | Sigenergy warrantyp.1–2, Minimum Throughput Energy table |
| Warranty conditions | Must stay connected to the internet for firmware updates. After 90 days offline the system enters Safe Operation Mode; more than one year offline in total cuts the warranty to 5 years from activation. | Sigenergy warrantyp.2, clause (v) |
| Compliance | ||
| UK grid compliance | Not documented in the sources we hold | |
Questions people ask
How much usable capacity does the Sigenergy SigenStor have?
5.84–8.76 kWh (Per module: BAT 6.0 = 5.84 kWh, BAT 10.0 = 8.76 kWh (100% depth of discharge, 0.2C, 25°C, start of life)).
Can the Sigenergy SigenStor be expanded?
1–6 battery modules per controller. Maximum usable storage: 52.56 kWh (calculated).
How long will the Sigenergy SigenStor run a house in a power cut?
Running essentials only (fridge-freezer, lights, Wi-Fi, TV and device charging, about 154 W on average), a full 6.0 SP controller + 1 × BAT 6.0 lasts roughly 36.1 hours. Heavy loads such as a heat pump, electric shower or EV charger cut this sharply. Use the calculator on this page with your own appliances.
What warranty does the Sigenergy SigenStor have in the UK?
10 years, guaranteeing 60% of capacity or 20.44–30.66 MWh of throughput, whichever comes first. SigenStor BAT 5.0/6.0/8.0/10.0 and EC SP/TP controllers, installed on or after 1 June 2023.
What does the Sigenergy SigenStor need to provide backup power?
Sigen Energy Gateway.
Head-to-head comparisons
Sigenergy SigenStor vs Tesla Powerwall 3
Price, capacity, power, warranty and runtime side by side.
Sigenergy SigenStor vs Fox ESS EVO 10
Price, capacity, power, warranty and runtime side by side.
Sigenergy SigenStor vs Huawei LUNA2000-S1
Price, capacity, power, warranty and runtime side by side.
Sigenergy SigenStor vs SolaX X1-IES
Price, capacity, power, warranty and runtime side by side.
Guides for the Sigenergy SigenStor
- Does the Sigenergy SigenStor work with Intelligent Octopus Flux?On Octopus's battery list.
- Does the Sigenergy SigenStor work with Octopus Charge Pack?On Octopus's battery list. Charge Pack works on Go, Intelligent Go, Flexible and fixed tariffs.
- How many SigenStor units do I need?Size it from your electricity use, heat pump, EV and backup plans.
- Can the Sigenergy SigenStor run a heat pump?How much of a cold winter day it covers.
Other batteries
Enphase IQ Battery 5P
An AC-coupled 5 kWh battery with six built-in microinverters, so it can be added to most existing solar systems. Up to seven can be combined in the UK.
myenergi libbi
A UK-designed modular battery with a 3.68 kW or 5 kW hybrid inverter and 1–4 battery modules (4.6 kWh usable each). Built to work with myenergi's zappi and eddi.
SolarEdge Home Battery 400V
A 9.7 kWh high-voltage battery that pairs with SolarEdge's single-phase Home Hub inverter. Up to three batteries per inverter. Octopus lists SolarEdge for Intelligent Octopus Flux.
Sunsynk W5.3 with ECCO inverter
A 5.32 kWh, 48 V wall-mounted IP65 battery module (4.79 kWh usable) used with Sunsynk's ECCO hybrid inverters. Add modules in parallel for more storage.
EcoFlow OCEAN 2
EcoFlow's second-generation stacked system: a single-phase hybrid inverter (3 to 6 kW) on top of OCEAN 2 LFP batteries of 4.87 or 7.76 kWh usable, up to six per stack.
AlphaESS SMILE-G3
AlphaESS's stacked single-phase system: a 3.68 or 5 kW hybrid inverter on top of one to four LFP battery modules of 4.56 or 9.12 kWh usable, up to 36.5 kWh.
Sungrow SBR
Sungrow's stackable high-voltage battery: 3.2 kWh LFP modules, 6.4 to 25.6 kWh per stack, all of it usable. Paired here with Sungrow's single-phase SH RS hybrid inverter (3 to 6 kW), which takes up to SBR192 (19.2 kWh).
Sources
- Sigen Battery 6.0 / 10.0 datasheet — Sigenergy. Retrieved 26 Sept 2026. Official Sigenergy copy (PDF created 17 Sep 2025). Two UK distributor copies carry the same figures.
- Datasheet – SigenStor Home (Energy Controller) — Sigenergy. Retrieved 26 Sept 2026. Sigenergy datasheet as published by a UK installer (the official site blocks automated downloads).
- Factory Limited Warranty for SigenStor (For Europe), 27/05/2025 — Sigenergy. Retrieved 27 Sept 2026. Official Sigenergy copy. Covers BAT 5.0/6.0/8.0/10.0 and EC 3.0–12.0 SP controllers installed on or after 1 June 2023.
Spotted an error? Every figure above links to the document it came from. See how we check data.