Sigenergy SigenStor vs SolaX X1-IES

Sigenergy SigenStor stores 5.84–8.76 kWh per unit, expanding to 52.56 kWh. SolaX X1-IES stores 4.6 kWh per unit, expanding to 18.4 kWh. Across the setups we list, continuous power is 3–6 kW for the SigenStor and 3–8 kW for the X1-IES. Warranty: 10 years vs 10 years. Cheapest published price per usable kWh: £341 for the SigenStor, £364 for the X1-IES, before installation; the SigenStor price excludes parts it needs. Intelligent Octopus Flux: SigenStor is “On Octopus's battery list”; X1-IES is “Not on Octopus's list”.

Figures from manufacturer documents, last checked 26 Sept 2026. We don't rank products or take payment for results.

How they're built

Sigenergy SigenStor

Modular: Energy Controller (hybrid inverter, solar on DC side) plus stacked battery modules. The batteries also work with Sigen Hybrid SP2/TP2 inverters via the SigenStor BC..

Backup: Sigen Energy Gateway.

Full SigenStor specs

SolaX X1-IES

All-in-one: hybrid inverter stacked on high-voltage LFP battery modules with a BMS; solar connects on the DC side.

Backup: Built-in EPS (backup) output.

Full X1-IES specs

Side by side

SpecificationSigenergy SigenStorSolaX X1-IES
Usable capacity (per unit)5.84–8.76 kWhPer module: BAT 6.0 = 5.84 kWh, BAT 10.0 = 8.76 kWh (100% depth of discharge, 0.2C, 25°C, start of life)Sigenergy datasheet, p.2, Usable energy capacity4.6 kWhPer TP-HS50E module. SolaX notes usable energy may vary with inverter settingsSolaX Power datasheet, p.2, Battery: Usable energy
Battery chemistryLFP (LiFePO₄), 314 Ah cellsSigenergy datasheet, p.2, Battery type and Cell capacityLFP (LiFePO₄)SolaX Power datasheet, p.2, Battery type
Maximum usable storage (expanded)52.56 kWhcalculatedPer controllerSigenergy datasheet18.4 kWhSolaX Power datasheet, p.2, System overview: 4 batteries
How it expands1–6 battery modules per controllerSigenergy datasheet, p.2, Number of modules per controller1–4 battery modules per inverter. Four modules need a second column and a Series BoxSolaX Power datasheet, p.2, System overview and Battery: Composition
Continuous power (per unit)3–6 kWSingle-phase controllers 3.0–6.0 kW; also limited by the battery modules (3 kW per BAT 6.0, 4.6 kW per BAT 10.0)Sigenergy datasheet, p.2, Single-phase controller, nominal output power3.68–8 kWX1-IES-3.7K: 3.68 kW · 5K: 5 kW · 6K: 6 kW · 8K: 8 kW (2.5 and 3 kW models also listed). Also limited by the batteries: 3 kW rated per moduleSolaX Power datasheet, p.2, AC output: Rated output power
Peak power4.5–9 kWSingle-phase backup peak for 10 seconds, 4.5–9 kW by controller. Battery peak: 4.5 kW per BAT 6.0, 6.9 kW per BAT 10.0Sigenergy datasheet, p.2, AC output (backup), peak 10 s7.36–16 kWcalculatedBackup peak for 10 seconds. Battery maximum power (5.1 kW per module, 8 kW per system) may limit thisSolaX Power datasheet, p.1, EPS output: Peak EPS output power
ArchitectureModular: Energy Controller (hybrid inverter, solar on DC side) plus stacked battery modules. The batteries also work with Sigen Hybrid SP2/TP2 inverters via the SigenStor BC.Sigenergy datasheet, p.2, Compatible inverters and footnote 4All-in-one: hybrid inverter stacked on high-voltage LFP battery modules with a BMS; solar connects on the DC sideSolaX Power datasheet, p.1–2
Max solar input6–12 kWSingle-phase controllers 3.0–6.0 SPSigenergy datasheet, p.2, DC input7.4–16 kW3.7K: 7.4 kWp · 5K: 10 kWp · 6K: 12 kWp · 8K: 16 kWpSolaX Power datasheet, p.2, PV input: Max. recommended PV array power
Backup switchover time0 msNeeds the Sigen Energy Gateway; load-side disruptionSigenergy datasheet, p.2, footnote 110 msLess than 10 msSolaX Power datasheet, p.1, EPS output: Switchover time
Backup needsSigen Energy GatewaySigenergy datasheet, p.2, footnote 1Built-in EPS (backup) outputSolaX Power datasheet, p.1, EPS (off-grid) output (with battery)
Indoor / outdoorNot documentedIndoor and outdoor (IP66)calculatedSolaX Power datasheet, p.2
Dimensions767 × 270 × 265 (per module)W × H × DSigenergy datasheet, p.2730 × 1226 × 210 (inverter + 2 modules)W × H × D. 1 module: 908 mm high; 3 modules: 1544 mm; 4 modules: two columnsSolaX Power datasheet, p.2, System overview: Dimensions
Weight62–78 kgPer module: 62 kg (BAT 6.0), 78 kg (BAT 10.0)Sigenergy datasheet, p.2, Weight87.2–181.2 kgInverter + 1 module 87.2 kg, + 3 modules 181.2 kg (47 kg per module)SolaX Power datasheet, p.2, System overview: Net weight
Warranty10 yearsSigenStor BAT 5.0/6.0/8.0/10.0 and EC SP/TP controllers, installed on or after 1 June 2023Sigenergy warranty, p.1, Limited Product Warranty table10 yearsBattery modules. The X1-IES inverter has 5 years, upgraded free to 10 years if it is connected to SolaX Cloud and uploads dataSolaX Power warranty, §2, Table 1 (T-BAT-SYS-HV-S50E, TP-HS50E)
Capacity guaranteed at end of warranty60%60% of usable energy for 10 years or the minimum throughput, whichever comes firstSigenergy warranty, p.1, Limited Performance Warranty70%70% of nominal energy (5.1 kWh per module)SolaX Power warranty, §3, Performance warranty of battery
Warranty conditionsMust stay connected to the internet for firmware updates. After 90 days offline the system enters Safe Operation Mode; more than one year offline in total cuts the warranty to 5 years from activation.Sigenergy warranty, p.2, clause (v)Bought from an authorised reseller and installed by a qualified installer. Batteries added later should be added within a year of installation. The inverter warranty is 5 years unless it's connected to SolaX Cloud.SolaX Power warranty, §1, §2 and §4

What they cost

Sigenergy SigenStor: from £2,990 for 8.76 kWh usable (£341 per usable kWh), not including a SigenStor Energy Controller.

SolaX X1-IES: from £6,700 for 18.4 kWh usable (£364 per usable kWh).

What the price buysPrice (inc. VAT)Per usable kWhNot included, or note
Sigenergy SigenStor BAT 6.0 battery module (one 5.84 kWh module)Retail, SigenStor£2,500£428A SigenStor Energy Controller (single-phase controllers listed below)
Sigenergy SigenStor BAT 10.0 battery module (one 8.76 kWh module)Retail, SigenStor£2,990£341A SigenStor Energy Controller (single-phase controllers listed below)
Sigenergy SigenStor Energy Controller 6.0 SP (single-phase hybrid inverter, no battery)Retail, SigenStor£1,270——
SolaX X1-IES 3.7 kW inverter + 1 × TP-HS50E battery (5.1 kWh)Retail, X1-IES£2,990£650—
SolaX X1-IES 3.7 kW inverter + 2 × TP-HS50E battery (10.2 kWh)Retail, X1-IES£4,200£457—
SolaX X1-IES 6 kW inverter + 2 × TP-HS50E battery (10.2 kWh)Retail, X1-IES£4,300£467—
SolaX X1-IES 6 kW inverter + 3 × TP-HS50E battery (15.3 kWh)Retail, X1-IES£5,900£428—
SolaX X1-IES 8 kW inverter + 4 × TP-HS50E battery (20.4 kWh)Retail, X1-IES£6,700£364—

Prices publicly advertised in the UK, seen 27 Sept 2026. Not quotes: they change, and installed prices depend on the home. Octopus says all its costs are based on April 2026 prices. Retail hardware prices include 20% VAT as shown by the seller. Per-kWh figures divide the price by the storage's usable capacity. All UK battery prices.

Smart tariffs: can Octopus run each battery?

Tariff or add-onSigenergy SigenStorSolaX X1-IES
Intelligent Octopus FluxOn Octopus's battery listNot on Octopus's list
Octopus Charge Pack (Go, Intelligent Go, Flexible, fixed)On Octopus's battery listComing soon, says Octopus
Octopus Flux, Cosy, Go and AgileWorks: you set the charge timesWorks: you set the charge times

From Octopus's own battery lists, checked 3 Oct 2026. To see what each tariff could save, use the battery arbitrage calculator.

Adding it to solar you already have

What each maker's documents say about fitting the battery alongside an existing solar inverter. Checked against the documents in our retrofit guides.

Sigenergy SigenStor

Modular: Energy Controller (hybrid inverter, solar on DC side) plus stacked battery modules. The batteries also work with Sigen Hybrid SP2/TP2 inverters via the SigenStor BC.

We haven't yet documented which existing inverters the SigenStor works with. See AC vs DC coupling for how a battery is added to existing solar.

SolaX X1-IES

All-in-one: hybrid inverter stacked on high-voltage LFP battery modules with a BMS; solar connects on the DC side.

We haven't yet documented which existing inverters the X1-IES works with. See AC vs DC coupling for how a battery is added to existing solar.

How long each runs your home in a power cut

Every setup we list for both, from a full battery with no solar. Appliance figures are typical estimates; use the calculator below with your own.

SetupUsableContinuousEssentials (fridge-freezer, lights, Wi-Fi, TV, charging)Essentials + air-source heat pump (cold day)
Sigenergy SigenStor · 6.0 SP controller + 1 × BAT 6.05.84 kWh3 kW36.1 hours3.2 hours
Sigenergy SigenStor · 6.0 SP controller + 1 × BAT 10.08.76 kWh4.6 kW2 days 6 hours4.8 hours
Sigenergy SigenStor · 6.0 SP controller + 2 × BAT 10.017.52 kWh6 kW4 days 12 hours9.6 hours
Sigenergy SigenStor · 6.0 SP controller + 3 × BAT 10.026.28 kWh6 kW6 days 18 hours14.4 hours
Sigenergy SigenStor · 6.0 SP controller + 4 × BAT 10.035.04 kWh6 kW9 days 1 hours19.2 hours
Sigenergy SigenStor · 6.0 SP controller + 5 × BAT 10.043.8 kWh6 kW11 days 7 hours24 hours
Sigenergy SigenStor · 6.0 SP controller + 6 × BAT 10.0 (maximum)52.56 kWh6 kW13 days 13 hours28.8 hours
SolaX X1-IES-3.7K + 1 battery (5.1 kWh)4.6 kWh3 kW28.4 hours2.5 hours
SolaX X1-IES-3.7K + 2 batteries (10.2 kWh)9.2 kWh3.68 kW2 days 9 hours5 hours
SolaX X1-IES-6K + 2 batteries (10.2 kWh)9.2 kWh6 kW2 days 9 hours5 hours
SolaX X1-IES-6K + 3 batteries (15.3 kWh)13.8 kWh6 kW3 days 13 hours7.6 hours
SolaX X1-IES-8K + 3 batteries (15.3 kWh)13.8 kWh8 kW3 days 13 hours7.6 hours
SolaX X1-IES-8K + 4 batteries (20.4 kWh, maximum)18.4 kWh8 kW4 days 18 hours10.1 hours

Try your own appliances

Tick what you want to run. Watts are typical UK figures (sources below the calculator); change them to match your appliances.
Essentials
Comfort
Kitchen
Big loads
Estimated runtime from full
36.1 hours

Average draw 154 W from 5.55 kWh available.

Everything on at once: 580 W — within the 3 kW limit

  • Starts from a full battery with 0% held back as reserve.
  • 5% extra allowed for wiring and standby losses on top of the manufacturer's usable figure.
  • Appliance figures are typical averages; your own may differ. Enter your own wattage for the most accurate result.
  • Assumes no solar recharging during the outage.
Where the appliance figures come from

Power ratings are the Centre for Sustainable Energy's typical UK figures. How much of the time each appliance runs comes from average UK use measured in the Household Electricity Survey (2010–11), converted to an average draw; newer appliances often use less. Heat pump figures come from the Electrification of Heat trial. Anything marked “estimate” is ours.

AppliancePowerHow much it runs
Fridge-freezerCSE typical rating: fridge-freezer 300 W. Start-up surge (600 W) is an EnergyPicker estimateCentre for Sustainable EnergyUK average 427 kWh a year for households with a fridge-freezer (Household Electricity Survey), about 49 W on averageNational Energy Action, PDF p.6–7, section 1.2 (Household Electricity Survey averages)
LED lighting (whole house)EnergyPicker estimate: about ten 10 W LED bulbsestimateEnergyPicker estimate: on half the timeestimate
Wi-Fi router & broadbandCSE typical rating: broadband router 10 WCentre for Sustainable EnergyEnergyPicker estimate: always onestimate
Laptop & phone chargingCSE typical rating: laptop 50 WCentre for Sustainable EnergyEnergyPicker estimate: charging about 7 hours a dayestimate
TV (LCD)CSE typical rating: LCD TV 120 WCentre for Sustainable EnergyEnergyPicker estimate: on about 6 hours a dayestimate
Gas boiler controls & pumpEnergyPicker estimate: check your boiler's manual for its electrical ratingestimateEnergyPicker estimate: running half the time in winterestimate
Chest freezerCSE typical rating: freezer 150 WCentre for Sustainable EnergyUK average 362 kWh a year for households with a chest freezer (Household Electricity Survey), about 41 W on averageNational Energy Action, PDF p.6–7, section 1.2 (Household Electricity Survey averages)
KettleCSE typical rating: kettle 3000 WCentre for Sustainable EnergyUK average 167 kWh a year for kettles (Household Electricity Survey), about 19 W on averageNational Energy Action, PDF p.6–7, section 1.2 (Household Electricity Survey averages)
MicrowaveCSE typical rating: microwave 1000 WCentre for Sustainable EnergyUK average 56 kWh a year for microwaves (Household Electricity Survey), about 6 W on averageNational Energy Action, PDF p.6–7, section 1.2 (Household Electricity Survey averages)
Electric hobCSE typical rating: hob 2000 WCentre for Sustainable EnergyUK average 226 kWh a year for hobs (Household Electricity Survey), about 26 W on averageNational Energy Action, PDF p.6–7, section 1.2 (Household Electricity Survey averages)
Electric ovenCSE typical rating: oven 2100 WCentre for Sustainable EnergyUK average 290 kWh a year for ovens (Household Electricity Survey), about 33 W on averageNational Energy Action, PDF p.6–7, section 1.2 (Household Electricity Survey averages)
Washing machineCSE typical rating: washing machine 2100 WCentre for Sustainable EnergyUK average 166 kWh a year for washing machines (Household Electricity Survey), about 19 W on averageNational Energy Action, PDF p.6–7, section 1.2 (Household Electricity Survey averages)
DishwasherEnergyPicker estimate: CSE doesn't list dishwashers; check your model's rating plateestimateUK average 294 kWh a year for dishwashers (Household Electricity Survey), about 34 W on averageNational Energy Action, PDF p.6–7, section 1.2 (Household Electricity Survey averages)
Tumble dryer (vented or condenser)CSE typical rating: tumble dryer 2500 WCentre for Sustainable EnergyEnergy labels give 560–640 kWh a year for condenser and vented dryers (160 cycles); we use 600 kWh, about 68 W on average. Heat pump dryers use far lessNational Energy Action, PDF p.34, energy label consumption
Electric showerCSE typical rating: electric shower 9000 WCentre for Sustainable EnergyEnergyPicker estimate: about 15 minutes a dayestimate
Air-source heat pump (cold day, about −3°C)Average, not peak: UK trial median 0.79 kWh per half hour at −3°C, i.e. 1.58 kW. The heat pump's own peak draw is higher; check its datasheetEnergy Systems Catapult, Table 10.1 (PDF p.79)Treated as a steady average across the dayEnergy Systems Catapult, Table 10.1 (PDF p.79)
EV charger (7 kW)EnergyPicker estimate: a typical single-phase home chargerestimateEnergyPicker estimate: charging about 2.4 hours a dayestimate
Worth knowing
  • SigenStor: Battery figures are for the current BAT 6.0 and BAT 10.0 modules (Sigenergy datasheet, September 2025). Older systems use BAT 5.0 (5.2 kWh usable) or BAT 8.0 (7.8 kWh usable) modules.
  • SigenStor: Warranty figures are from Sigenergy's Europe warranty (May 2025). It doesn't name the UK; confirm UK cover with your installer. The earlier (2024) edition promised 70% capacity; the 2025 edition promises 60% with higher throughput limits.
  • SigenStor: Round-trip efficiency is not stated as a single figure in the datasheets we hold.
  • SigenStor: UK retailers also sell 8, 10 and 12 kW single-phase controllers; our controller datasheet covers the 3.0–6.0 SP range, so setups here use the 6.0 SP.
  • X1-IES: Continuous power per setup is the lower of the inverter rating and 3 kW rated power per battery module; each module can briefly deliver up to 5.1 kW.
  • X1-IES: Round-trip efficiency isn't stated; the datasheet gives the inverter's maximum efficiency (97.6%), which is one conversion only.
  • X1-IES: Warranty figures are from SolaX's global warranty terms (V1.7, for products sold from 10 September 2026). It doesn't mention the UK specifically; UK distributors may add their own terms.
  • X1-IES: The system overview in the datasheet labels usable energy in "kW"; the battery table gives 4.6 kWh per module, which we use.

Questions people ask

Which is cheaper, Sigenergy SigenStor or SolaX X1-IES?

Their cheapest published prices cover different parts, so the per-kWh figures aren't like for like. Sigenergy SigenStor: from £2,990 for 8.76 kWh usable (£341 per usable kWh), not including a SigenStor Energy Controller. SolaX X1-IES: from £6,700 for 18.4 kWh usable (£364 per usable kWh). These are published prices before installation, so add the parts each needs and the installer's price. These prices include 20% VAT; installed in your home by an installer, a battery is zero-rated for VAT until 31 March 2027 (HMRC).

Which stores more, Sigenergy SigenStor or SolaX X1-IES?

Sigenergy SigenStor has the higher stated maximum. Sigenergy SigenStor: up to 52.56 kWh (per controller). SolaX X1-IES: up to 18.4 kWh. Per unit, Sigenergy SigenStor stores 5.84–8.76 kWh and SolaX X1-IES stores 4.6 kWh.

Which can run more appliances at once?

Across the setups we list, Sigenergy SigenStor delivers 3–6 kW continuously and SolaX X1-IES delivers 3–8 kW. These are the maximums for each setup; installers can set some systems lower. Continuous power limits how many appliances can run at the same time; capacity decides how long they run.

Which has the better warranty?

Sigenergy SigenStor: 10 years, 60% capacity guaranteed at the end. SolaX X1-IES: 10 years, 70% capacity guaranteed at the end. Conditions differ, so check the warranty rows in the table above.

Do Sigenergy SigenStor and SolaX X1-IES work with Octopus's smart battery tariffs?

Intelligent Octopus Flux: SigenStor on Octopus's battery list; X1-IES not on Octopus's list. Charge Pack: SigenStor on Octopus's battery list; X1-IES coming soon, says Octopus. Standard Octopus Flux, Cosy Octopus, Octopus Go and Agile work with any battery whose charge times you can set yourself.

Other comparisons

Sources

  1. Sigen Battery 6.0 / 10.0 datasheet — Sigenergy. Retrieved 26 Sept 2026.
  2. Datasheet – SigenStor Home (Energy Controller) — Sigenergy. Retrieved 26 Sept 2026.
  3. Factory Limited Warranty for SigenStor (For Europe), 27/05/2025 — Sigenergy. Retrieved 27 Sept 2026.
  4. SolaX X1-IES Datasheet (EN) V1.7 — SolaX Power, V1.7. Retrieved 27 Sept 2026.
  5. SolaX Warranty Terms & Conditions (V1.7, Global version) — SolaX Power, V1.7. Retrieved 27 Sept 2026.
  6. Sigenergy SigenStor Solar Battery Module with LED (product page, 6.0 and 10.0 variants) — AIZO Quality Heating. Retrieved 27 Sept 2026.
  7. Sigenergy SigenStor Energy Controller Single Phase EC SP 3.6–12 kW (product page, all variants) — AIZO Quality Heating. Retrieved 27 Sept 2026.
  8. Intelligent Octopus Flux (tariff page and battery eligibility checker) — Octopus Energy. Retrieved 3 Oct 2026.
  9. What is Charge Pack and how does it work? — Octopus Energy. Retrieved 3 Oct 2026.
  10. SolaX X1-IES 3.7kW All-In-One Single-Phase Energy Storage System Bundle (product page, all battery options) — AIZO Quality Heating. Retrieved 27 Sept 2026.
  11. SolaX X1-IES 6kW All-In-One Single-Phase Energy Storage System Bundle (product page, all battery options) — AIZO Quality Heating. Retrieved 27 Sept 2026.
  12. SolaX X1-IES 8kW All-In-One Single-Phase Energy Storage System Bundle (product page, all battery options) — AIZO Quality Heating. Retrieved 27 Sept 2026.
  13. VAT on energy-saving materials and heating equipment (VAT Notice 708/6) — HM Revenue & Customs, Last updated 31 January 2024. Retrieved 26 Sept 2026.

Spotted an error? See how we check data. Always confirm your final design with an MCS-certified installer.